121 GB/T 14235.5-1993 熔模铸造模料 表面硬度测定方法 Testing method for surface hardness of pattern materials in investment casting
122 GB/T 14235.6-1993 熔模铸造模料 酸值测定方法 Testing method for acid number of pattern materials in investment casting
123 GB/T 14235.7-1993 熔模铸造模料 流动性测定方法 Testing method for fluidity of pattern materials in investment casting
124 GB/T 14235.8-1993 熔模铸造模料 粘度测定方法 Testing method for viscosity of pattern materials in investment casting
125 GB/T 14235.9-1993 熔模铸造模料 热稳定性测定方法 Testing method for thermal stability of pattern materials in investment casting
126 GB/T 14408-1993 一般工程与结构用低合金铸钢件 Low alloy steel castings for general engineering and structural purposes
127 GB/T 15055-1994 冲压件未注公差尺寸极限偏差 Permissible stamping varitions in dimensions without tolerance indication
128 GB/T 15056-1994 铸造表面粗糙度 评定方法 Evaluation method on cast surface roughness
129 GB/T 15111-1994 点焊接头剪切拉伸疲劳试验方法 Test method for shear tensile fatigue of spot welded joints
130 GB/T 15114-1994 铝合金压铸件 Aluminium alloy die-castings
131 GB/T 15115-1994 压铸铝合金 Die casting aluminium alloys
132 GB/T 15116-1994 压铸铜合金 Die casting copper alloys
133 GB/T 15117-1994 铜合金压铸件 Copper alloy die castings
134 GB/T 15169-1994 钢熔化焊手焊工资格考核方法 Approval testing of manual welders--Fusion welding-steel
135 GB/T 15620-1995 镍及镍合金焊丝 Nickel and nickel alloy welding wires
136 GB 15735-1995 金属热处理生产过程安全卫生要求 Requirements for the safety and health in production process of metal heat treatment
137 GB/T 15747-1995 正面角焊缝接头拉伸试验方法 Method of tension test for front fillet welded joint
138 GB/T 15825.1-1995 金属薄板成形性能与试验方法 成形性能和指标 Sheet metal formability and test methods--Formability and indexes
139 GB/T 15825.2-1995 金属薄板成形性能与试验方法 通用试验规程 Sheet metal formability and test methods--General test rules
140 GB/T 15825.3-1995 金属薄板成形性能与试验方法 拉深与拉深载荷试验 Sheet metal formability and test methods--Drawing and drawing load test
141 GB/T 15825.4-1995 金属薄板成形性能和试验方法 扩孔试验 Sheet metal formability and test methods--Hole expanding test
142 GB/T 15825.5-1995 金属薄板成形性能与试验方法 弯曲试验 Sheet metal formability and test methods--Bending test
143 GB/T 15825.6-1995 金属薄板成形性能与试验方法 锥杯试验 Sheet metal formability and test methods--Conical cup test
144 GB/T 15825.7-1995 金属薄板成形性能与试验方法 凸耳试验 Sheet metal formability and test methods--Earing test
145 GB/T 15825.8-1995 金属薄板成形性能与试验方法 成形极限图(FLD)试验 Sheet metal formability and test methods--Forming limit diagram (FLD) test
146 GB/T 15826.1-1995 锤上钢质自由锻件机械加工余量与公差一般要求 Machining allowances and tolerances for steel open die forgings on hammer--General reguirement
147 GB/T 15826.2-1995 锤上钢质自由锻件机械加工余量与公差盘、柱类 Machining allowances and tolerances for steel open die forgings on hammer--Disks and columns
148 GB/T 15826.3-1995 锤上钢质自由锻件机械加工余量与公差 带孔圆盘类 Machining allowances and tolerances for steel open die forgings on hammer--Disk swith holes
149 GB/T 15826.4-1995 锤上钢质自由锻件机械加工余量与公差 圆环类 Machining allowances and tolerances for steel open die forgings on hammer--Rings
150 GB/T 15826.5-1995 锤上钢质自由锻件机械加工余量与公差 套筒类 Machining allowances and tolerances for steel open die forgings on hammer--Seamles cylinder hushings
151 GB/T 15826.6-1995 锤上钢质自由锻件机械加工余量与公差 光轴类 Machining allowances and tolerances for steel open die forgings on hammer--Shaft without steps
152 GB/T 15826.7-1995 锤上钢质自由锻件机械加工余量与公差 台阶轴类 Machining allowances and tolerances for steel open die forgings on hammer--Shaft with steps
153 GB/T 15826.8-1995 锤上钢质自由锻件机械加工余量与公差 单拐曲轴类 Machining allowances and tolerances for steel open dle forgings on hammer--Single throw crankshaft
154 GB/T 15826.9-1995 锤上钢质自由锻件机械加工余量与公差 黑皮锻件 Machining allowances and tolerances for steel open die forgings on hammer--Forging without machining
155 GB/T 15829.1-1995 软钎焊用钎剂 分类、标记与包装 Soldering fluxes--Classification, labelling and packaging
156 GB/T 15829.2-1995 软钎焊用钎剂 树脂类钎剂 Soldering fluxes--Resin basis fluxes
157 GB/T 15829.3-1995 软钎焊用钎剂 有机物类钎剂 Soldering fluxes--Organic fluxes
158 GB/T 15829.4-1995 软钎焊用钎剂 无机物类钎剂 Soldering fluxes--Inorganic fluxes
159 GB/T 16253-1996 承压钢铸件 Steel castings for pressure purposes
160 GB/T 16672-1996 焊缝 工作位置 倾角和转角的定义 Welds--Working positions--Definitions of angles of slope and rotation
161 GB/T 8541-1997 锻压术语 Terminolgy of forging and stamping
162 GB/T 16743-1997 冲裁间隙 Blanking clearance
163 GB/T 16746-1997 锌合金铸件 Zinc alloy castings
164 GB/T 1175-1997 铸造锌合金 Casting zinc alloys
165 GB/T 16923-1997 钢件的正火与退火 Normalizing and annealing of steel parts
166 GB/T 16924-1997 钢件的淬火与回火 Quenching and tempering of steel parts
167 GB/T 16957-1997 复合钢板焊接接头力学性能试验方法 Mechanical tests on welded joints in clad plates
168 GB/T 6060.1-1997 表面粗糙度比较样块 铸造表面 Roughness comparison specimens Cast surfaces
169 GB/T 5611-1998 铸造术语 Foundry terminology
170 GB/T 5680-1998 高锰钢铸件 Austenitic manganese steel castings
171 GB/T 9442-1998 铸造用硅砂 Foundry silica sand
172 GB/T 17445-1998 铸造磨球 Cast grinding balls
173 GB/T 12467.1-1998 焊接质量要求 金属材料的熔化焊 第一部分: 选择及使用指南 Quality requirements for welding--Fusion welding of metallic materials--Part 1: Guidelines for selection and use
174 GB/T 12467.2-1998 焊接质量要求 金属材料的熔化焊 第二部分: 完整质量要求 Quality requirements for welding--Fusion welding of metallic materials--Part 2: Comprehensive quality requirements
175 GB/T 12467.3-1998 焊接质量要求 金属材料的熔化焊 第三部分: 一般质量要求 Quality requirements for welding--Fusion welding of metallic materials--Part 3: Standards quality requirements
176 GB/T 12467.4-1998 焊接质量要求 金属材料的熔化焊 第四部分: 基本质量要求 Quality requirements for welding--Fusion welding of metallic materials--Part 4: Elementary quality requirements
177 GB/T 17493-1998 低合金钢药芯焊丝 Low alloy steel flux cored electrodes for arc welding